2 Strokes Down Under

Posted: **Sun Nov 27, 2011 5:54 pm**

Anybody got any waterbottle (suzuki GT750) bits lying around.....

Engine bits/electrics/chambers etc.

Graham

Posted: **Sun Nov 27, 2011 6:32 pm**

A guy in the VJMC is selling a complete bike dismantled, he wants 2k for it. I can get you his details if you like.

Posted: **Sun Nov 27, 2011 9:32 pm**

I really only want engine bits for this thing....

I probably will need a few bits....sooner rather than later....

But I will take the details in case he just wants to sell the bits I need.

email me at crsallora@gmail.com

Thanks, Graham

Posted: **Tue Nov 29, 2011 4:29 pm**

PM sent

Posted: **Tue Nov 29, 2011 11:55 pm**

thanks Pat,

Graham

Posted: **Wed Nov 30, 2011 8:10 am**

Have you got a spare cylinder?

Posted: **Wed Nov 30, 2011 2:23 pm**

Graham,did your dad have a blue one of these many years ago?I think he might have even set up as a drag bike?
If I remember right,he lived near Fairfield/Smithfield?Pm if u want.

Posted: **Wed Nov 30, 2011 4:50 pm**

My Dad never sat on a motorbike as far as I know..... I did however have a drag bike that I made in 1990 in SA that I run a few times in the NT and SA.

That's my son who was 14 back then... Its a Subaru Brumby 1800cc motor with a GM 271 blower.

Homemade slider clutch using 3 x datsun plates, I found an old alcohol high pressure pump from a rocket at Woomera (I worked there for a while) so i made a mechanical injection system.....similar to a Hilborn system.

I did a 8.79 1/4 back in 1993 @ 159mph.....a fun thing to ride.

Not a twostroke though.... sometimes a trip to the dark side makes you appreciate things more!!!!

Graham

Posted: **Wed Nov 30, 2011 6:36 pm**

hey graham, I know a bloke in melbourne with a blue watterbottle sidecar...

let me know if you wish to speak to him and Ill track down his contact details... im memory serves me correctly he has a heap of bits and denco (or similar) cylinders

Posted: **Wed Nov 30, 2011 6:42 pm**

ahhh good old ebay

cylinders

http://www.ebay.com.au/itm/Suzuki-GT-75 ... 4840wt_952

exh bits

http://www.ebay.com.au/itm/Suzuki-GT750 ... 345wt_1185

http://www.ebay.com.au/itm/Suzuki-1974- ... 500wt_1202

http://www.ebay.com.au/itm/1976-Suzuki- ... 1677wt_952

http://www.ebay.com.au/itm/1973-77-SUZU ... 402wt_1084

loom
http://www.ebay.com.au/itm/SUZUKI-GT750 ... 1227wt_952

Posted: **Fri Dec 30, 2011 2:04 pm**

Hi Graham what are you after I have one full bike one spare motor and early barrell with the carb stubs cut and rewelded to down draft carbs. It will need finish porting but nice for a racer. I also have porting specs and race info for t500 and gt750 with and without barrel spacers. Pm if any sounds of use. Link

2 Strokes Down Under

waterbottle bits needed.

waterbottle bits needed.

Re: waterbottle bits needed.

Re: waterbottle bits needed.

Re: waterbottle bits needed.

Re: waterbottle bits needed.

Re: waterbottle bits needed.

Re: waterbottle bits needed.

Re: waterbottle bits needed.

Re: waterbottle bits needed.

Re: waterbottle bits needed.

Re: waterbottle bits needed.